The INA is a low power, dual instrumentation amplifier offering excellent accuracy. Its versatile. 3-op amp design and small size make it ideal for a. Part No.：, LH Download：, Download Right selection Save Target As View Datasheet (Html) No need to install PDF reader software. Description. Request National Semiconductor Corporation lh Instrumentation Amplifier, single,bipolar,quad,12pin,metal online from Elcodis, view and download lh .
|Published (Last):||19 December 2006|
|PDF File Size:||20.34 Mb|
|ePub File Size:||8.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Common Mode Range 10V for. Should a higher CMRR be desired, pin 9 should be left open and the procedure, in this section followed. By similar analysis V,2 is seen to be: As can be seen for identically matched resistors. It also should be noted that large signal bandwidth.
This current must flow through Rise as shown in Figure For applications requiring a lower source impedance. The LH is a 2 stage amplifier with a high. Under worst case conditions: Bias Current Return Path. Figure 11 is a plot of bandwidth versus RB. The implication is that a finite impedance must.
Operational amplifier, A” receives.
(PDF) LH0036 Datasheet download
The amplifier’s slew rate in this configuration is typically O. A resistor Raw may be placed between pin 1 and ground to accomplish this purpose. An internal factory trimmed resistor, R6, will. National Semiconductor Electronic Components Datasheet. Should a higher CMRR be desired, pin 9 should. The value of the resistor is dictated by. In the standard configuration, pin 1 of the LH Pin 2 of the LH is provided as a guard drive.
Pin 2 will always be biased at the input common. G 4 As can lhh0036 seen for identically matched resistors, eCM is cancelled out, and the differential gain is dictated by equation 4. The source impedance looking into pin 2 is approximately 15 kD. In some applications, particularly at low frequency, it may be desirable to limit bandwidth in order to mini- mize the overall noise bandwidth of the device. In applications in which the signal source is float.
Pin 9 should be grounded for nominal operation. LH may be inserted between pin 2 and the. Use of Guard Adtasheet applications requiring a lower datashest impedance than 15′ kD, a unity gain buffer, such as the LH dattasheet be inserted between pin 2 and the input shields as shown in Figure Figure 11 is a.
Figure 3 is plot of slew rate versus Raw.
LH0036 Datasheet PDF
The source impedance looking into. Rise causing a voltage rise at point A. National Semiconductor Electronic Components Datasheet. Guard Pin With Buffer. LlW lh00366 k 1. Proper use of the. Equation 5a re-arranged in more convenient form may be used to select RG for a desired gain: The amplifier’s slew rate in.
lh National Semiconductor Corporation, lh Datasheet
A, also receives input e2 via A2 and R2. Pin 8 is also l0h036 to improve the common mode. For the LH, equation 4 reduces to: Pin 2 will always be biased at the input common mode voltage. Bandwidth vs Raw It also should be noted that large signal bandwidth and slew rate may be adjusted down by use of Raw. Simplified LH Datashee LH is a 2 stage amplifier with a high input impedance gain stage comprised of A, and -A 2 and a differential to single-ended unity gain stage, A3.
Off-set may be nulled using the circuit shown in. The closed loop gain may be set to any value from. The value of the resistor is dictated by the maximum input bias current, and the common mode ly0036. Figure 10 is a plot of input bias current versus.
The implication is that a finite impedance must be supplied between the input and power supply ground. The LH exhibits input bias currents typically.
Figure 2 shows typical small daasheet bandwidth versus R BW.