IPC Moisture Sensitivity Classification for Non-IC Components. Content Provider Association Connecting Electronics Industries [IPC]. IPC, PWB Assembly Sol- dering Process Guideline for. Electronic Components. • IPC, Moisture Sensitiv- ity Classification for Non-IC. Components. and Use of Moisture/Reflow Sensitive Surface Mount Devices). This standard supersedes IPC Developed by ECA, IPC and JEDEC.
|Published (Last):||18 September 2016|
|PDF File Size:||14.43 Mb|
|ePub File Size:||11.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
For shelf life requirements 903 one year place a in the Q. Orders over pieces must be supplied on a minimum of two 2 reels or minimum reel package quantity.
Use of newsprint, excelsior, 9530 loosed fill expanded polystyrene is not allowed as a means of cushioning. Parts must be loaded consecutively from left to right, proceeding from top to bottom as viewed with the notch of the waffle pack positioned in the upper left hand corner with a consistent separation between rows and columns.
SMI only General Requirements: Items that are gold plated or have a 16 finish or lower shall contain the following note marked on exterior of container: Tray capacity will be indicated on the purchase request. Leaded surface mount technology electronic components must be packaged such that component lpc integrity is not adversely affected during shipping by contact with the packaging.
The carrier shall be of a construction to allow component removal without tooling. So typically paper as it enters the waste stream The lid must be capable of being removed without disturbing the ippc within the tray and the part no. Exterior containers shall comply with uniform freight and national motor freight classification rules or regulations or other carrier rules, as applicable to the mode of transportation. A rigid container that holds one leaded component.
Elements or components that are Class 0 Sensitive shall be clearly marked as Class 0 on the external 99503 of the packaging. Do not handle with bare hands; use clean, lint free cotton gloves when handling. All waffle packs containing items that are ESD sensitive diodes, integrated circuits, etc.
Each moisture barrier bag shall be marked with the part number, date code, quantity, and serial numbers of the PWBs enclosed. Matrix Tray General Requirements: Tape and Reel Only General Requirements: Use of individual bags or containers shall be used to insure adequate protection from physical contact with other parts.
Tubes Only General Requirements: Moisture transfer refers to the fact that certain solid waste Static generating materials should be avoided.
Tubes for Surface-Mounted Components Definition: With the notch of the waffle pack in the upper left hand corner, parts must be loaded left to right, and top to bottom. All components must be loaded into black static dissipative 4″x4″ waffle packs.
Compliance Commitments related to the manufacture and.
Packaging Requirement Codes
Minimum cavity depth is the same height as that of the component. Basin and Range Province PowerPoint. The parts must not be held in the pockets by supplementary means within the tray. Components will be covered with a lint free filter paper insert s between the top of the component and the bottom of the cover 4.
Packaging Requirement Codes
A maximum of 5 devices shall be contained in a tray. Items that are ESD iipc shall be individually, electrostatically protected using appropriate industrial ippc. The packaging shall allow the polarity or part number markings to be visible for each device. The carrier shall be designed such that the component does not move when the carrier is opened and the lead configuration does not change once the component is removed from the carrier.
Suppliers should attempt to provide a best fit solution without incurring extensive tooling costs. Gel Trays should remain the same for subsequent lots of the same component type. Specific packaging requirements will be provided by the using factory through the supplier electronic replenishment process.
Tray covers will also consists of lpc static dissipative material held to the base with a one piece clip.
Use of newsprint, excelsior or upc fill expanded polystyrene shall be avoided as a means of cushioning. This code shall only be used on product provided by through Integrated Supplier Partnering Agreements. Moisture content may be assured by documented process controls or appropriate testing. Special Packaging Package parts per instructions specified by purchase order or subcontracts, i. Oxide Sensitive devices shall be vacuum sealed in moisture proof antistatic material.
Additional information on this requirement can be found at the following site: A carrier that holds multiple components in a row. Parts do not have to be pre-oriented, but must be face up. Best Commercial Practice Packaging of parts shall be sufficient to afford protection against deterioration and physical damage during shipment from the supply source to BAE Systems.
Waffle pack capacity should be maximized within a manufacturing lot. The Gel retention level must be the minimum required to hold the component with a mesh size that adequately supports the component and allows the component to be released with vacuum applied. If there are any questions contact Microwave Manufacturing Engineering 6.
Use of newsprint, excelsior, or loosed fill expanded polystyrene shall be avoided as a means of cushioning. Documents Flashcards Grammar checker.
Gel Trays must be labeled on the cover and the bottom of the base with the supplier lot number and part number, PO number and BAE part number.
The preferred cavity size should be mils.