Figure 1: ICEpowerA. Size: 10 x 10 x cm. General Description. The ICEpowerA is a general purpose amplifier solution. By using patented. Cheap Electronics Stocks, Buy Directly from China Suppliers:icepower a icepowerA iceA D class power amplifier digital amplifier module board . Cheap Network Cards, Buy Directly from China Suppliers:Digital power amplifier module of icepower A icepowerA D power amplifier digital amplifier.

Author: Tek Negrel
Country: Saint Lucia
Language: English (Spanish)
Genre: Art
Published (Last): 3 May 2010
Pages: 410
PDF File Size: 8.24 Mb
ePub File Size: 5.86 Mb
ISBN: 668-4-38826-499-3
Downloads: 6205
Price: Free* [*Free Regsitration Required]
Uploader: Nikobei

However, it must be mentioned, that you have probably misread the specs of the Icepower products. Top curve icepoder amplitude response. I figured the issue was the speaker. We supply the Icepowfr. However, it doesn’t matter, since we obviously do not use the A, otherwise we would have communicated the W power.

Thanks for the help! It is likely that you have looked up the phase responce graph, instead of the frequency responce. Also, are there icepwer – 3dB BW measurements at 8 ohm loading for the A? I was for certain not looking at the phase response, it was definitely the frequency response curve.

Ah, that makes sense. I went back and looked at the Icepower A -3dB upper bandwidth spec, it’s only 3 kHz albeit at 4 ohms, likely a little higher at 8 ohms. It comes down to what is in there. Any errata sheets for the data sheet?


w Digital Amplifier Class D Switch Power Supply Board for ICEpower a | eBay

Nice that you have found your tone. I have purchased a KPA unpowered rack unit and intend to use that with the GTFX for live use, and I’ll use the toaster with the Quilter 1000aa rehearsals and recording.

Since I bought it, I have had many comments from fellow bandmates in the bands I have been in or am in regarding how dark the sound was from the cab, icepoder high end. I suspect this is an error in their documentation.

I haven’t wanted to open it up and look at what is inside, I’m afraid to void the warranty. This agrees with the 30 kHz value.

Icepower A Bandwidth – Profiler related discussions – Kemper Profiler Forum

That will put it to rest. Therefore there was no need to go above 3khz.

This is icepowef shown on page 9 pf v1. Then, for grins and chuckles, I tried running the toaster monitor out into my Quilter Tone Block into the Gemini 1-P, and it really opened it up. Thanks for reaching out.

I would like to check and see if the typical -3dB bandwidth at 4 ohm loading value of 3 kHz, as given in the data sheet see highlighted line on page 5 of attachment is a correct value? The power amps go up to 30 kHz with an error of less ice;ower a dB, according to the specs. Take it as you will. We’re talking pre-Armstrong here!


It sounds darned near just like the PA tone. Well, I LIKE having a cab behind or sometimes in front of me interacting with the guitar, and I like the traditional cab look.

3500w Digital Amplifier Class D Switch Power Supply Board for ICEpower 1000a

I went through several setups too before I fell in love with the same rig. If you would like to icelower all features of this site, it is mandatory to enable JavaScript. Hopefully this post will not upset too many Power Head fans, but I would 1000a to post my observations about the Power Head with the Icepower A amplifier and the Power Rack as well I assume, since they use the same power amplifier. So all’s well that ends well.

A power amp that has its 3 dB corner at 3 kHz would have been unsalable even 50 years ago.