HCNW 4504 PDF

HCNW Broadcom / Avago High Speed Optocouplers 1Ch 12mA mW datasheet, inventory & pricing. The HCPL and HCPL contain a GaAsP LED while the. HCPL-J and HCNW contain an AlGaAs LED. The LED is optically coupled to an. Buy Broadcom HCNW# in Avnet Americas. View Substitutes & Alternatives along with datasheets, stock, pricing and search for other Transistor .

Author: Kecage Doujar
Country: Latvia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 16 June 2015
Pages: 464
PDF File Size: 6.54 Mb
ePub File Size: 7.79 Mb
ISBN: 175-2-92232-760-2
Downloads: 82994
Price: Free* [*Free Regsitration Required]
Uploader: Nirr

Logic High Output Current vs. These optocouplers are suitable for “safe electrical isolation” only within the safety limit data.

However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. For technical assistance call: Separate connections for the photodiode bias and outputtransistor collector increase the 404 up to a hundred times that of a conventional phototransistor coupler by reducing the base collector capacitance.

See Option data sheet for more information. When inverter power transistors switch Q1 and Q2 in Figure 17it is essential that they never conduct at the same time. Device considered a two-terminal device: Option data sheets available. Therefore, optocouplers with tight propagation delay specifications and not just shorter delays or lower pulse-width distortion can achieve short dead times in power inverters.

Inverters can also be designed such that the power transistor turns off when the optocoupler LED turns on; this type of design, however, requires additional fail-safe circuitry to turn off the power transistor if an over-current condition is detected. Use of nonchlorine activated fluxes is highly recommended. Under TTL load and drive conditions: There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances.

  AKADEMICKA PRIRUCKA PDF

The difference between the maximum and minimum values depends directly on the total spread in propagation delays and sets the limit on how good the worst-case dead time can be for a given design.

HCNW4504#300

The LED is optically coupled to an integrated high gain photo detector. An insulating layer between a LED and an integrated photodetector provide electrical insulation between input and output. Contact Agilent sales representative or authorized distributor for information. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.

Calculating the maximum dead time is slightly more complicated. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be hcnq as an input-output continuous voltage rating.

Extremely large currents will flow if there is any overlap in their conduction during switching transitions, potentially damaging the transistors and even the surrounding circuitry. Propagation Delay Time vs. The timing illustrated in Figure 17 assumes that the power transistor turns on when the optocoupler LED turns on.

These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. To ensure this, hcw turn-on of the optocoupler should be delayed by an amount no less than tPLHmax – tPHLminwhich also happens to be the maximum data sheet value for the propagation delay difference specification, tPLH – tPHL.

HCNW 데이터시트(PDF) – Agilent(Hewlett-Packard)

Current Transfer Ratio vs. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. F bypass capacitor between pins 5 and 8 is recommended.

  DEMOCRACIA TOTALITARISMO RAYMOND ARON PDF

F bypass capacitor connected between Pins 5 and 8 is recommended. Most inverters are designed such that the power transistor turns on when the optocoupler LED turns on; this ensures that both power transistors will be off in the event of a power loss in the control circuit. The importance of hcbw specifications is illustrated in Figure DC and Pulsed Transfer Characteristics. It is important to maintain accurate LED turn-on delays because delays shorter than tPLH – tPHL max may allow shootthrough currents, while longer delays will increase the worst-case dead time.

Maintenance of the safety 44504 shall be ensured 44504 means of protective hcnq. The LED signal to turn on Q2 should be delayed enough so that an optocoupler with the very fastest turn-on propagation delay tPHLmin will never turn on before an optocoupler with the very slowest turn-off propagation delay tPLHmax turns off.

Minimizing this dead time is an important design goal for an inverter designer. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. Although tPLH-tPHL max tells the designer how much delay is needed to prevent shoot-through current, it is insufficient to tell the designer how much dead time a design will have.

Use of a 0.