CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.
|Published (Last):||21 June 2006|
|PDF File Size:||5.69 Mb|
|ePub File Size:||8.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Crestron CP2 Operation Manual
Use Crestron Certified Wire. Insert the tinned connection into the Cresnet connector and tighten the retaining screw. If further assistance is required, please contact a Crestron customer service representative. Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices.
This Agreement may only be modified by a writing signed by an authorized officer of Crestron. Bussing Strip Installation The 2-Series integrated dual bus control system is supplied with two brass bussing strips to facilitate commoning linking of manal terminal block connections. Device is not receiving sufficient power.
CRESTRON CP2 OPERATION MANUAL Pdf Download.
Such flexibility can offer a cost-effective solution for system expansion, providing a host of additional control ports in a single module. Replace crrestron with the same or equivalent type recommended by the manufacturer. For example, a Cresnet run using 18 AWG Crestron Certified Wire and drawing 20 watts should not have a length of run more than feet.
Failure to do so could cause equipment damage or void the Crestron warranty.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed.
Hardware or software failure, hardware incompatibility with software definitions or programming error. CRESTRON shall not be liable to honor warranty terms if the product has been used in any crestrkn other than that for which it was intended, or if it as been subjected to misuse, accidental damage, modification, or improper installation procedures.
Use Crestron power supplies for Crestron equipment. As such Crestron cannot and does not guarantee any results of use of the Software or that the Software will operate error free and You acknowledge that any development that You perform using the Software or Host Application is done entirely at Your own risk.
Use Crestron Toolbox to display the error log. If Cresnet units are to be daisychained on the run, the Cresnet power usage of each network unit to be daisychained must be added together to determine the Cresnet power usage of the entire chain. Page 28 Crestron Electronics, Inc. Such flexibility can offer a cost-effective solution for system expansion, providing a host of additional control ports in a single module.
Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. The Software is licensed and not sold.
Contact with thermal insulating materials should be avoided on all sides of the unit. Apply solder only to the ends of the twisted wires. Software License Agreement This Agreement may only be modified by a writing signed by an authorized officer of Crestron. Insufficient power can lead to unpredictable results or damage to the equipment. You shall not remove or conceal any trademark or proprietary notice of Crestron from the Software including any back-up copy.
The bussing strips are constructed with four terminal block positions and may be trimmed to size for various applications or different devices. If the unit is a home-run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Refer to software release notes or Crestron website for other required Crestron software packages. When calculating the length of wire for a particular Cresnet run, the wire gauge and the Cresnet power usage of each network unit to be connected must be taken into consideration. Confirm properly defined signal definition in the program.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Upload program and firmware. Programming Software SystemBuilder from the Crestron website and examine the extensive help file. Verify that proper IR or serial port is defined. However, there is no guarantee that interference will not occur in a particular installation.
Use care in wiring installations to avoid applying 24 VDC to Cresnet wiring from an AC power pack as well as from a system device that contains its own power supply.