ASTM D2584 PDF

ASTM D is used to determine ignition loss of cured reinforced resins and can be used to examine the remaining fiber post burning. If only glass. ASTM A/AM Steel, Sheet and Strip, Heavy-Thickness Coils, Hot- Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy. This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Plastics.

Author: Takasa Brakasa
Country: Burundi
Language: English (Spanish)
Genre: Music
Published (Last): 19 December 2009
Pages: 58
PDF File Size: 13.35 Mb
ePub File Size: 5.3 Mb
ISBN: 420-3-63930-126-1
Downloads: 24212
Price: Free* [*Free Regsitration Required]
Uploader: Zolom

Standards can be obtained from appropriate standard authorities. Astn comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

ASTM D2584 – 11

NOTE 2—It is often convenient to use samples obtained from specimens that have been tested for mechanical properties such as? Each test result was the average of three individual determinations. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Send us a request Wilton UK: Care must be taken that the ignition does not proceed so rapidly that there will be a mechanical loss of the noncombustible residue.

ASTM D – 08 Standard Test Method for Ignition Loss of Cured Reinforced Resins

An Ash test is used to determine if a material is filled. The data in Table 1 should not be applied to acceptance or rejection of materials, as these data apply only to the materials tested in the round robin and are unlikely to be rigorously representative of other lots, formulations, conditions, materials, or laboratories. Maintain such a temperature asstm the specimen burns at a uniform and moderate rate until only ash and carbon remain when the burning ceases.

A magnified optical examination of the ash residue is performed to determine if the ash is glass, mineral, or a combination of both. This service is not available if you are a URL user where you do not log in with an email address. Validating the specifications, value and safety of your raw materials, products and assets. Number of specimens tested by PTLI: NOTE 4—It is not absolutely necessary to ignite the specimen in a bunsen?

  FRANZ ROSENZWEIG STAR OF REDEMPTION PDF

Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

It cannot identify individual percentages in multi-filled materials without additional test procedures being performed. Need help or have a question? The desiccator is not required if the test is performed only to examine the?

Heat the crucible and specimen in a bunsen? Summary of Test Method 3. The test will identify the total filler content.

Webprint Printed and bound. TGA Thermogravimetric Analysis is an alternative method to determine filler content with smaller samples sizes.

Identification of Filler If the supplied material has mineral filler an FTIR analysis of the ash residue can help to further identify the type of mineral.

Standards can be ast from appropriate standards authorities.

ASTM D2584:02

Users of this test method should apply the principles outlined in Practice E to generate data speci? Typically the average of 3 crucibles is reported. If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Precision and Bias For each material, all the samples were prepared at one source, but the individual specimens were prepared at the laboratories which tested them.

Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. It is obtained by pooling the within-laboratory standard deviations of the test results for all of the participating laboratories: The benefits of a subscription: Smaller sample weights can be tested but accuracy diminishes with smaller sample sizes. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

  LA ANTORCHA Y LA ESPADA RICK JOYNER PDF

Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. The test will identify the total filler content. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.

Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Auditing Consulting Sourcing Training. You need to log in before adding standards to the monitoring service. A magnified optical examination of the ash residue is performed to determine if the ash is glass, mineral, or a combination of both. Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.

The conditioning is not required if the test is only performed to examine the? Formally confirming that your products and services meet all trusted external and internal standards.

NOTE 3—Materials that have gross differences in the ratio of resin to reinforcement within an area as small as 2. This standard has been approved for use by agencies of the Department of Defense.

An ash test cannot be used to determine the percent carbon fiber or percent carbon black since carbon burns off during the Ash test. Inspection Validating the specifications, value and safety of your raw materials, products and assets. Start Webshop Product catalog Product presentation. An Ash test is used to determine if a material is filled. If only glass reinforcement and organic resin were present, the ignition loss can be considered to be the resin content.