SPIRALCO is a company specialized in the production of spiral-weld steel tubes and pipes. May 23, 1 This speciﬁcation speciﬁcation is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys Stainless Alloys. ASTM A Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded ( Sizes NPS 16 and Over) Reprinted from the Annual Book of ASTM Standards.
|Genre:||Health and Food|
|Published (Last):||8 November 2004|
|PDF File Size:||1.96 Mb|
|ePub File Size:||18.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
Note 1—Acceptability for many services may be controlled by codes or standards such as those published by the American National Asm Institute and American Society of Mechanical Engineers.
ASTM A134 Carbon Steel Pipes, Size: 16
Pipe shall be furnished with a plain right angle cut or with bevel ends as specified. New York, NY The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. It is the re respo sponsi nsibil bility ity of the use userr of thi thiss sta standa ndard rd axtm est establ ablish ish appro app ropri priate ate saf safety ety and hea health lth pra practi ctices ces and det determ ermine ine the applicability of regulatory limitations prior to use.
Steel Pipes in Mumbai.
Tensile strength ,min Ksi Mpa. The number of production weld tests shall be one per each lot of joints or fraction thereof, but not less than one for each welder or welding operator.
Note 4—The dimensionless designator NPS nominal pipe size has been substituted in this standard for such traditional terms as “nominal diameter”, “size”, and “nominal size”. All repaired pipe shall be tested hydrostatically. Note 2—For testing methods not specifically covered in this specification, reference can be made to Test Methods and Definitions Awith particular reference to Annex A 2 on Steel Tubular Products.
Active view current version of standard. Acceptability for many services may be controlled by codes or standards such as those published by the American National Standards Institute and American Society of Mechanical Engineers.
Disposition shall be a matter of agreement between the purchaser and the manufacturer.
We need your help to maintenance this website. Closer tolerances may be established by agreement between the manufacturer and the purchaser. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Finished pipe shall be commercially straight.
The wall thickness and weight for welded pipe under this specification shall be governed by the requirements of the specifications to which the steel was ordered. This standard does not purport to address all of the safety concerns, if any, associated with its use. The weld-test specimens for the reduced-section tension test shall be taken perpendicularly across the weld and the test pieces shall have the weld in the middle of the specimen.
ASTM A Carbon Steel Pipes, Size: 16, Superior Steel Overseas | ID:
This standard does not purport to address all of the safety concerns, if any, associated with its use. Carbon Steel Seamless Pipe. Finished pipe shall be commercially straight.
In this specification hard or rationalized conversions apply to diameter, lengths, and tensile properties. Closer tolerances may be established by agreement between the manufacturer and the purchaser. This abstract is a brief summary of the referenced standard.
Historical Version s – view previous versions of standard. A1334 weld-test specimens for the reduced-section tension test shall be taken perpendicularly across the weld and the test pieces shall have the weld in the middle of the specimen. The pressure shall be determined by the following equation: Soft conversion applies to other SI measurements.
C List of world top ten steel producing nations during Nov Defects in the welds, such as sweats or leaks, shall be repaired or the piece rejected at the option of the manufacturer. For keeping the developed products in a secure manner, we have maintained a capacious warehousing unit. Hydrostatic Test Note 5 Sstm is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
Thank you for interesting in our services.
Closer tolerances may be established by agreement between the manufacturer and the purchaser. Please help us to share our service with your friends.
This specification covers electric-fusion arc -welded straight seam or spiral seam steel pipes with diameters Asm 16 and larger. Please copy and paste this embed script to where you want to embed Embed Script.