View and Download ABB Advance Optima Uras 14 service manual online. Advance Optima Uras 14 Measuring Instruments pdf manual download. Manuals and User Guides for ABB Advance Optima Uras We have 1 ABB Advance Optima Uras 14 manual available for free PDF download: Service Manual. Spare Parts for ABB & Siemens Gas Analyzer & Sample Handling Systems is available. Home» Products» ABB Gas Analyzer Spare Parts» Module Uras
|Published (Last):||13 October 2004|
|PDF File Size:||1.30 Mb|
|ePub File Size:||5.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sample cell, continued Versions Sample cell length options are shown in the table below. The reference measurement range is calculated from the initial measurement range. Hold the cell up to a light and look through it. Pressure sensor Accessories Multimeter Voltage Electrical value: Seller assumes all responsibility for this listing.
ABB ADVANCE OPTIMA URAS 14 SERVICE MANUAL Pdf Download.
Cyclical Cycle Time Default: Measurement signal not sensitive enough Indication 1 Measured values too low even after calibration performed 2 Analyzer sensitivity has lessened Status message For 1: IR detectors, continued Detector The data in the following tables are guidelines. Page 67 Status messages, continued Status messages IR detector Fault code Status message Brief description General error 0x Temperature control Control deviation 1, 2 or erroneous error temperature measured value 0x Temp.
The calibration unit is a motorized shifting device for the calibration cells. Multimeter, oscilloscope Voltage Electrical value: Module versions Chapter 3: Module versions Summary Module ursa principles Module versions plastic tubing connections Module versions stainless steel tubing Ex analyzer module Chapter 3: Apertures Location in module The apertures and their adjustment screws are located on the main frame between the modulator and sample cells.
Flow detector General An internal flow sensor can be used to measure throughput. Hardware configuration Module hardware The Uras 14 analyzer module is equipped according to the measurement task involved. Connecting Cable Connecting cable Location in module Connection between IR module circuit board and optical components. No ueas messages Status messages Details Uraas cause Measures Improper sample gas preparation – Check the cooler – Check dew points of sample gas and, if applicable, zero gas Sample components in zero gas Replace zero gas Inadequate purge time prior to zero Temperature detectors, continued Temperature Temperature detector 1 is used for temperature compensation of IR components.
URAS 14 Gas Analyzer Ao2020 ABB 2431-0-111100000000 Ao2000 **
The modulator consists of: Step Action Turn off the analyzer power supply. Contents, Fortsetzung Chapter 4: Linearization values are allocated by the software for various components. An item that has been professionally restored to working order by a manufacturer-approved vendor. Skip to main content. Page Postlinearization, continued Result correction Postlinearization results in the calculation of parameters A2NL and A4 NL and parameters these are applied to further linearization calculations.
This item may or may not be in its original packaging. No status messages For 2: They are shown in a inset to the cross section of the sample cells installed in the sample and reference chambers. Electrical connections What electrical The following connections are always present: Hood with supplemental heater Location in module The hood encloses the optical components. Summary, continued Figure Analyzer module Uras 14 open 1 Calibration unit 2 2 Measurement cell 2 3 Main frame with aperture control 4 Beam path 2 aperture adjustment screw 5 Modulator with emitters not visible 6 Calibration unit 1 7 Infrared detector 1 8 Beam path 1 aperture adjustment screw 9 Measurement cell Temperature detectors Temperature detector The temperature detector control T-Regl.
Structure A land divides the cell into a sample chamber and a reference chamber; there is a gas link between the two.
Uras 14 Gas Analyzer AO ABB AO *Refurbished* | eBay
Pull the thermal link T out of anb base support. Page 95 Chapter 6: Page Temperature detectors, continued Component configuration Component Component name e. Page Software configuration with TCT, continued Detector selection The following wbb are relevant to the Uras 14 analyzer module: Introduction Chapter contents In this chapter you will find the following information: Learn More – opens in a new window or tab International postage and import charges paid to Pitney Bowes Inc.
Have one to sell? None Status messages Details Possible cause Measures Contamination at sample gas collection – Clean contaminated components and point and in lines check, if applicable, sample gas preparation temperature control – Check system shutdown procedure – Check urae Calibration Cell General Calibration cells are used for internal calibration of the analyzer module. A maximum of 2 detectors are possible per beam path.
ABB Advance Optima Uras 14 Manuals
Two screws in each case need to be removed. They are not dependent on the measurement range selected. Please check with your country’s customs office to determine what these additional costs will be 144 to bidding or buying.