I bought a Sodick wire EDM and installed is what happend: Computer starts up, and power buttons works i saw the pomp. We offer a huge range of Sodick & CNC repair services. GET IN CAN YOU REPLACE MY MONITOR ON MY EX 21 A SODICK MACHINE? YES, we. evening all,a couple of years back I got a a with mark 21 controller. well the controller is now toast and I was lucky to get a mark

Author: Kajikus Dijar
Country: Mongolia
Language: English (Spanish)
Genre: Environment
Published (Last): 25 May 2014
Pages: 289
PDF File Size: 14.25 Mb
ePub File Size: 7.46 Mb
ISBN: 953-2-69540-127-4
Downloads: 74297
Price: Free* [*Free Regsitration Required]
Uploader: Daizshura

Thanks for your answer.

Sodick A don’t power up

Electrical Discharge Machining vs. A D screen failed contacted manufacturers agent was quoted a very high price contacted SD — IQ solutions who offered me an alternative replacement screen of the machine. I have an external HP floppy drive, and have just read my old mark21 disks ok. This is the reason our customers sldick before anything else.

So there must be another prblem causing this problem. Called up tech support from the Sodick web page. Specialisation in servo amplifier testing and repair used throughout the EDM a32 examples given below: Tags for this Thread controllermarksetsodicksodick a a mark The table seems to move easily in all directions without any bumping of hinderance.

Your work is pretty impressive! Are the four big red switches at the bottom of the cabinet all on? Results 1 to 10 of The machine came with a transformer dodick various voltage. Results 1 to 6 of 6. I am still cautious but the machines seems OK for now.

Few minutes on hold they answered.


Originally Posted by graydog If your machine fails, don’t panic. What sort of wire are you suggesting I look at?

sodick A // A mark 25 controler

A quick Google s320 will find him. Ill have a lot of work to map the electronics over to the bed after that. Sorry I couldn’t be of much more help.

Soidck be happy to help you if you can tell me how. For me, the machine is to learn. I got stuck at this screen: We only replace the parts which need to be replaced so we guarantee to beat the original quotation.

Sodick Wire EDM

Very pleased with a comprehensive service which took place and everything was checked with some impartial advice given. It seems to fault just as the table should start moving, not in the middle of a move. But i saw the pomp rotates the wrong direction, so I changed 2 wires.

Found Larry’s emailI’ll give it a try. PCB Repairs PCB repairs our trained technicians will carry out sophisticated diagnostic and repair to identify the defective components on the PCB during this process we will a3220 replace time critical components this significantly minimises the chance … Read more.

But like all things sodick During this visit, machine operating systems hard drives were copied giving me a complete backup which was of importance to me since I have had hard drive failures in the past which had affected my production schedules.

I dont have any schematics to send but i usually check at the connection at the motor and ssodick it back best i can. The time now is SD — IQ solutions will replace individual cables soodick repair them which will give you a significant cost saving or replacing the whole unit we will use your existing parts to keep the cost down.


Have you checked your incoming power inside the control cabinet as well as at the breaker box -Looks all fine. Posted via Mobile Device.

It has run with this at the previous owner and at my place, but I put the power on only for a short time because there was no water in the tank, I thought it had to be bad for the sofick running dry. Any help would be appreciated. So far so good. He can be contacted through EDM Network.

We provide advanced repair services at low costs

We think the issue has been resolved. Efficient professional service, would use again. A MK 25 machine had a fault on it, constant short-circuit diagnosed on the telephone. I replaced the power source with a new, bit more powerfull one.

So I made the machine ready for a test and then it sodicm Thank you again for the reply. This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy.

Other Machining Processes February 3, Did you by chance turn off the pumps by flipping the pump switch on the tank by accident -might be, there are some tiny switches not sure what those are doing. Computer starts up, and power buttons works also.